Get a Quote

5L rotovap - Lab Instrument Manufacturer

A rotovap (rotary evaporator) is a device used in chemical laboratories for the efficient and gentle removal of solvents from samples by evaporation. The process of rotary evaporation is most often used to separate solvents with low boiling points, such a n-hexane or ethyl acetate, from compounds which are solid at room temperature and pressure.

Ethyl Acetate - Health Effects

A) Ethyl acetate is low in toxicity. It is a mild mucous membrane irritant, but is not caustic. In high concentrations it may be a CNS depressant. Animal studies have demonstrated pulmonary edema, decreased cardiac contractility, seizures and hepatic damage, but these have NOT been reported in humans. CHRONIC EXPOSURE.

How can I remove ethyl acetate - ResearchGate

Add approximately 2-3 mL of DCM and rotavap the sample. Repeat this three more times. This will completely remove Ethyl acetate. You can use vacuum after that if needed. Cite 7 Recommendations 21st...

Solved Answer the following questions based on the ... - Chegg

After the extractions, remove the ethyl acetate using a rotovap – what is this solid? Acidify the bicarb. layer using HCl. How do you know when the aqueous layer has been acidified? ... Procedure: Dissolve phensuprin (0.5 g) in ethyl acetate (25 mL) and stir for 1-3 min. Measure out 0.5-1.0 g of phensuprin and put it in a beaker along with 25 ...

How to use a Rotary Evaporator - University of California ...

Apr 01, 2010 A typical rotavap uses a variable speed sparkless induction motor that spins at 0-220 rpm and provides high constant torque. A good setting here is 7-8. 5. The aspirator vacuum is turned on. On most models, the vacuum on/off control is managed by turning a stopcock at the top of the condenser (left side of the above diagram).

Author: Subject: Replacing DCM with Ethyl Acetate or ...

Dec 09, 2021 Ethyl acetate is my go-to solvent for extractions. It is generally a good alternative to DCM in that application. Isopropyl acetate would probably work just as well, though it has a higher boiling point so it will be a little more annoying to evaporate/distill off of your product, especially if you aren’t using a rotovap.

Buchi 20/40/60 rule for Rotary Evaporators

Doc: CHEMFS rotovap pressure-temp Custodian: Dept. Chem. School Safety Coordinator Page 1 of 1 Created: Feb 2005 Last Review : Dec 2010 Next Review: Dec 2013 Buchi 20/40/60 rule for Rotary Evaporators Optimal Distillation parameters for a rotary evaporator vary according to solvent in use: 1. Set water ...

CHEZ 301 Extraction Full Lab Report - CHEZ 301 - Organic ...

During extraction of acetanilide a rotovap was used t o form the solid through the. evaporation of ethyl acetate. After the extractions, percent compositions was calculated from. each of the three components. These compositions were 23% for sucrose, 74% …

Title: Rotary Evaporator Page 1 of 6 ROTARY EVAPORATOR

Ethyl Acetate 141-78-6 77 -3 IB 2, 3, 0 serious eye irritation Toluene 108-88-3 110 4 IB 2, 3, 0 teratogen, specific organ toxicity ... ☐Note placed in front of the rotovap to indicate to others what chemicals are being used. ☐Solvent trap is emptied and bump trap is cleaned prior to use.

Buchi R-200/R-210 Rotavapor - University of York

Ethyl Acetate 77.1 35 Methanol 64.7 30 Pet Ether 40-60 40-60 20 Pet Ether 60-80 60-80 25 Toluene 110.6 45 Water 100 45 Coil condenser Air bleed tap Flask clip Angle adjuster Rotation control Water in/out To main vacuum tap Lifting handle Joint clip Solvent collection flask Temperature control and readout ...


ETHYL ACETATE ETA 9.20 SATURATED LIQUID DENSITY Temperature (degrees F) Pounds per cubic foot 35 40 45 50 55 60 65 70 75 80 85 90 95 100 57.620 57.410 57.190 56.980 56.760 56.550 56.330 56.100 55.880 55.660 55.430 55.200 54.970 54.730 9.21 LIQUID HEAT CAPACITY Temperature (degrees F) British thermal unit per pound-F 15 20 25 30 35 40 45 50 …

Ethyl acetate CH3COOC2H5 - PubChem

Ethyl acetate is the acetate ester formed between acetic acid and ethanol. It has a role as a polar aprotic solvent, an EC (pyroglutamyl-peptidase I) inhibitor, a metabolite and a Saccharomyces cerevisiae metabolite. It is an acetate ester, …

Ethyl acetate miscible with water

Ethyl acetate miscible with water Liquid-liquid extraction and recrystallization extraction is one of the most ancient known chemical operations; It involves the transfer of a solute from one phase to another. The preparation of a cup of tea or coffee represents a process of extraction of flavor components and smell from dryed material in water.

Ethyl acetate - EtOAc Ethyl acetate - Sigma-Aldrich

Ethyl acetate. CH3COOC2H5. Synonyms: EtOAc, Ethyl acetate. CAS 141-78-6. Molecular Weight 88.11. Browse Ethyl acetate and related products at MilliporeSigma.

Rotovap tricks - CEN

Jul 04, 2016 Rotovap tricks July 4, 2016 | A version of ... We have thus routinely been able to remove higher-boiling solvents such as ethyl acetate and cyclohexane at a water bath temperature of 35–40 C ...


Jul 13, 2015 ethyl acetate 1. identification product name: ethyl acetate synonyms: ethyl ester acetic ether cas no: 141-78-6 chemical formula: c4-h8-o2 use: solvent, for industrial use only 2. hazards identification highly flammable irritating to the eyes repeated exposure may cause skin dryness or cracking

Azeotropes in Rotary Evaporation Blog -

Jun 21, 2021 In the case of an acetic acid and water mixture, an appropriate entrainer would be ethyl acetate. A 69.2% aqueous solution of ethyl acetate forms an azeotrope with a boiling point of 70.4C. When you add the correct amount of ethyl acetate to the water/acetic acid mixture, you can easily distill off the resulting azeotrope to leave pure acetic acid.

Putting the Rule of 20 Into Practice Blog -

May 08, 2020 In general, your bath temperature should be 20C higher than the boiling point of the substance you want to evaporate. And your coolant should be 20C or more lower than the vapor temperature. For example, if the boiling point of your substance is 40C, a bath temperature of 60C and coolant temperature of 20C should provide an optimal setup.

Solved What else do you need to do to purify 1 and ... - Chegg

Nothing, they are already pure Re-dissolve this solid in ethyl acetate and extract it with HCI. 3 will remain in the ethyl acetate, which can be removed by the rotovap. and 2 will be in the aqueous layer which should be acidified and the solid collected by vacuum filtration Remove the ethyl acetate from Question 14 to isolate 4.

Sciencemadness Discussion Board - removal of pyridine ...

Nov 12, 2009 I chose the ethyl acetate wash according to your advice since the pH is high, and then I will get rid of ethyl acetate by rotovapping. The fullerene was processed in ethyl acetate before and with the help of the rotovap we were able to obtain pure compounds ~95% level. [Edited on 1-14-2010 by andre178]

Rotary Evaporator Fact Sheet - UMass Amherst

Remove and clean the bump bulb from the rotovap immediately after use to ensure ground glass joint connections do not stick together and to prevent contamination of future samples that will be rotovaped. ... ethyl acetate 77.1 . o. C 9.1 . o. C hexane 68.7 . o. C -2.3 . o. C heptane 98.4 . o. C 22.3 . o. C methanol 64.7 . o. C 5.0 . o. C .

Rotary Evaporation to Remove Solvent Organic Chemistry ...

Rotary evaporation is a technique commonly used in organic chemistry to remove a volatile solvent from a non-volatile compound of interest. Invented by Lyman C. Craig in 1950 the rotary evaporator, or rotovap, gently removes solvents from compounds using heat combined with reduced pressure to evaporate, dry, and purify samples for further downstream use.

RE-2000E 1L Rotary Evaporator - Rotovap

Rotary evaporator, also known as rotovap or rotavap, is a common used lab instrument in chemical laboratory, and mainly used for the continuous distillation of large amount easily volatilized solvents under negative pressure. ... Rotary evaporator is mostly used for isolating low-boiling ingredient, such as hexane, ethyl acetate, that ...

Solvent Boiling Points Chart - BrandTech Scientific Inc.

Solvent Boiling Points Chart (all boiling points at standard pressure) Solvent Boiling Point (C) Solvent Boiling Point (C) Acetic Acid 118.0 Ethyl Acetate 77.1 Acetic Acid Anhydride 139.0 Ethyl Ether 34.6 Acetone 56.3 Ethylene Dichloride 83.5 Acetonitrile 81.6 Ethylene Glycol 197.5 Benzene 80.1 Heptane 98.4 iso-Butanol 107.7 n-Hexane 68.7 n-Butanol 117.7 Hydrochloric …

How does rotary evaporation work? -

The rotovap works by increasing the rate of evaporation of the solvent by (1) reducing the pressure to lower the solvent boiling point, (2) rotating the sample to increase the effective surface area and (3) heating the solution. ... Try diluting with water and then extracting into ethyl acetate or ether, and use a lot of whichever solvent you ...

Activation of silent biosynthetic gene clusters using ...

The supernatant of fermentation broth was adjusted to pH ~3 by adding HCl, and then mixed with equal volume of ethyl acetate. Organic phase was dried using rotovap, and then dissolved in 1 ml of methanol. After being filtered by 0.2 μm filter, the crude extract was injected into HPLC. All HPLC analyses were carried out on Agilent 1260 ...

Heidolph Instruments : Solvent data

Water. H 2 O. 100.0. 72. Xylene (isomeric mixture) C 8 H 10. 137–143. 25. Download solvent data as PDF.

Rotary Evaporators Rotary Evaporation -

What is a rotary evaporator? Rotary evaporators are used in distillation for efficient and gentle removal of solvents from samples through evaporation. This method is normally applied to low boiling solvents such as n-hexane and ethyl acetate from compounds that would normally be solid at room temperature and normal atmospheric pressure.

Contact Us
advanced technology

High-tech Zone, Zhengzhou, China

Inquiry Online
Related Post
Leave Us Message
customer service img

We immediately communicate with you

Get Quote Online

If you have any needs or questions, please click on the consultation or leave a message, we will reply to you as soon as we receive it!

<script type="text/javascript" src=""></script>